WEEK 17- Check Plagiarism of FYP Report.

OBJECTIVE:

- To check my plagiarism of my FYP report.

CONTENT & PROCEDURE:

- First, I need to submit my FYP report to my supervisor Dr. Mohd Zaki Bin Ayob to see if it needs to be improved.

- Next, Dr. Zaki will check the plagiarism of this report through the fyp portal.

- The result of plagiarism must be below 20%.

RESULT/ ANALYSIS:

- Alhamdulillah, for plagiarism of my report only 16 %.

- Next, i will proceed to send my report to printing company and submit my report at FYP portal UniKL BMI.

CONCLUSION:

Dr. Mohd Zaki Bin Ayob

- As a conclusion, alhamdulillah in this semester I was able to succeed in my FYP project. I would like to special thank to my supervisor Dr. Mohd Zaki bin Ayob for his guidance, advice and his patience from the beginning of this project. I would also like to apologize to Dr. Zaki  if I made a mistake in making this project. I am also very lucky to have a supervisor like Dr. Zaki helped me from the start until I succeeded in this project .I also want to thank Dr Nabila and Mr Ku Halim who helped and gave me permission to test my project and get the results at Pusat Pembiakan Kambing Bebiri Pokok Sena Kedah.

WEEK 16- Video of Result for FYP presentation

OBJECTIVE:

- To show my video of result from my project.

CONTENT & PROCEDURE:

- This video i will put in the result section of my slide.

- Contain of video:

• The component use for this project.
• The project test works.
• Result receive image via email.
• Type behavior of goat.
• Result captured image produce from Sound sensor and PIR sensor.

The video can see at this link at Youtube:

https://www.youtube.com/watch?v=wHc6j_STLCw

WEEK 15- Preparation for slide presentation

OBJECTIVE:

- To make a preparation of slide presentation for FYP presentation.

CONTENT & PROCEDURE:

- For the FYP presentation will be conduct on 2 July 2020.

- For the presentation, all student need to make a video presentation duration 10 minutes.

- Slideshows should contain the following:

-Tips for FYP presentation

• Try to minimize words in our presentation as possible as we can.
• Maximize our verbal communication.
• Not to mention any advantage of our system, instead we can say that is limitation of our project and we will try to accomplish it in our future work.
• Our whole concentration should be to the audience not the slides.
• Before any of the audience say ' I have a question' best approve is you should ask 'Any question'.
• Take up to 5 seconds break at each slide even after you are finished.
• Try to mention the chief guest in your audience while presenting.
• Say something good in favor of audience when you have finished the presentation.  

- For my slide presentation, i will record by using Screen O-Matic.

- For result part, i will make a short video of my project functioning and also include video of goat behaviour. 

CONCLUSION:

As a conclusion, first i need to plan the structure of my slide presentation. After that i will show my slide to my supervisor to check if the slide need to improve.  

WEEK 14- Flow chart and Blog Diagram of project

OBJECTIVE:

- To review my flowchart and blog diagram of project.

CONTENT & PROCEDURE:

-      First the project starts with running the coding at python. The Sound sensor and PIR sensor detect if something suspicious occur in the barn. If Sound sensor detects loud noise around 95- 112 dB or PIR sensor detects movement within 4 meters, it will send signal to Raspberry pi and Pi camera to capture the image of the situation. Then, the user will get alert message that contain image captured by Pi camera from email.  

Description:

Input

To determine the situation of the animal in danger, we use the Sound Sensor and PIR Sensor.  The sound sensor is one type of module used to notice the sound. Generally, this module is used to detect the intensity of sound. PIR sensor is electronic sensor that measures infrared (IR) light radiating from objects in its field of view. They are most often used in PIR-based motion detectors. Sound sensor function is to detect a loud noise made by a goat when something happens while PIR sensor is to detect motion if there is an intruder. For application both sensor in this project to detect and measure the rate of sound and movement occurring at the barn.

 

Process

This system using Raspberry Pi 3b+ with Pi camera. The Raspberry Pi is a very cheap computer that runs Linux, but it also provides a set of GPIO (general purpose input/output) pins that allow you to control electronic components for physical computing and explore the Internet of Things (IoT). The function of Raspberry Pi in this project to sending image in jpeg file to email user that generate from Pi camera if Sound sensor and PIR sensor produce high signal.

Output

In this project, phone is our output that receive image from email if the sensor detects suspicious situation occur at the barn.  

  

CONCLUSION:

- As a conclusion, this flowchart and blog diagram review about how my project works.

WEEK 13- Second day Test Project at Pusat Pembiakan Bebiri Pokok Sena

OBJECTIVES:

- To adjust the actual sensitivity sensor of my project.

- To make observation of  goat behavior. 

CONTENT & PROCEDURES:

- First, setup the project at walkway in the middle at the barn.

 

Figure 1: View of project setup

- Next, run the coding of project at Python software and see it result.

- If the result does not match the expected result, adjust the sensitivity of both sensors.

- After that, by using Sound meter to measure the level of noise produce from goat in the morning and evening at the barn.

- Then, make a observation of goat behavior when be caught, sick and hungry.  

RESULT @ ANALYSIS:

- For Sound sensor sensitivity we set above 95 dB while the PIR sensor sensitivity within 4 meters.

Figure 2: Goat behavior when be caught

- Next, for my observation of goat behavior when be caught, the goat be aggressive and make loud noise around 95- 102 dB. 

Figure 3: Goat behavior when sick

- For the second behavior when the goat is sick, the goat do not make any sound, look less active and skinny.

Figure 4: Goat behavior in the morning

- In the morning, the goat seem very active and make loud noise around 98- 112 dB. This is because, in this situation they are very hungry at that time.   

- In the evening, the goat behavior is still active but produce less noise compare in the morning. In this time, they can produce noise around 85- 89 dB.

CONCLUSION:

- As a conclusion, my project working well and get good result. Next, i also know the type of goat behavior in the different time and situation. 

WEEK 12- Test project at Pusat Pembiakan Kambing Biri-Biri at Pokok Sena

OBJECTIVE:

-To test and get primary result of project.

-To get readings of sound produced by the goats.

CONTENT/ PROCEDURE:

- First, setup the project at the barn with the right location to get a better image.

- Then setting the sensitivity of sensor.

Figure 1: Progress setup of project

- Next, run the coding at python and see it result.

- Next step, try to measure the reading of sound produce by goat with using Sound meter app on the phone. 

Figure 2: Sound meter apps

RESULT & ANALYSIS:

-First result motion detected.

-In this situation, we tried to make a move in the lane to see the result of the PIR sensor.

Figure 3: The PIR sensor detect motion produced from human.

- Second Result detected by sound.

- In this situation, the worker catches the goat to see the result of the sound sensor if the goat produces a loud noise when in danger.

Figure 4: The sound sensor detected loud noise produced from goat.

- Next, the result reading from sound meter.  

Figure 5: The reading of sound meter when the goat in danger situation is 105 db

Figure 6: The reading of sound meter when the goat in steady situation is 85 db

CONCLUSION:

- As a conclusion, my project work well but i need to adjust the sound sensor to get the right sensitivity because most of the result is detected by PIR sensor. So for the next week, i will test again my project at the barn and also take a reading of sound produce by goat because the farmer inform that the goat had a difference behaviour at difference time. They explain to me, in the morning the goat make a loudly noise because they are hungry. So, i will take the reading from sound meter in the morning to see the result at that time. 

WEEK 11- Test project at Home

OBJECTIVE:

- To test and see the result of project.

CONTENT/ PROCEDURE:

- First setup the project connection and setting it position to get a good view.

Figure 1: View setup position of project

- After that, run the coding and see it result. 

RESULT & ANALYSIS:

Result 1

Figure 2: Images generated from sound sensors

 

Result 2

Figure 3: Image generated from motion sensor

CONCLUSION:

As a conclusion, my project is functioning well and it get good result similar like expected result. For the next week, i will test my project at the Pusat Peternakan Kambing Biri-Biri Pokok Sena to adjust the sound produce from goat for sound sensor.